quadient DS-200iQ Скачать руководство пользователя страница 136

Страница: 136 / 231

In-line Version

To adjust the Output Conveyor rollers, first loosen the thumb screw knobs on both

sides.

Adjust the rollers so that the ejecting envelopes contacts the nip (pinch) point of

the rollers at the conveyor surface, and then falls fully onto the surface as shown

below.

Re-tighten the thumb screw knobs once the desired adjustments have been made.

Output Conveyor Backrest Adjustment

When the envelopes reach the end of the conveyor, they will stack up against the

backrest which can be adjusted to suit the required amount of tilt.

To adjust the Output Conveyor backrest, first loosen the thumb screw knobs on

each side.

134

| Page 134 | May-29-2020 11:33 |

Operator

Instructions

Содержание DS-200iQ








































































































































































































































Результаты поиска

Содержание DS-200iQ

Отзывы:

quadient DS-200iQ, Руководство пользователя, Страница: 136 / 231

Результаты поиска

Содержание DS-200iQ

Отзывы: