background image

Notices 

iii 

 

 

 

Safety Warnings

 

 

1.

 

The XCubeNXT can operate normally in the temperature of 0ºC~40ºC (31.99 ~ 103.99°F). Please 
make sure the environment is well-ventilated.

 

2.

 

The power cord and devices connected to the XCubeNXT must provide a correct supply voltage 
(100-127V~/ 10A, 50-60Hz. 200-240V~/ 5A, 50-60Hz).

 

3.

 

Do not place the XCubeNXT in direct sunlight or near chemicals. Make sure the temperature 
and humidity of the environment are in the optimized level.

 

4.

 

Place the product right side up at all times.

 

5.

 

Unplug the power cord and all connected cables before cleaning. Wipe the XCubeNXT with a 
dry towel. Do not use chemical or aerosol to clean the storage. 

6.

 

Do not place any objects on the XCubeNXT for the server’s normal operation and to avoid 
overheat.

 

7.

 

Use the screws provided in the product package to lock the hard disks in the XCubeNXT when 
installing hard disks for proper operation.

 

8.

 

Do not place the XCubeNXT near any liquid.

 

9.

 

Do not place the XCubeNXT on any uneven surface to avoid falling off and damage.

 

10.

 

Do no place the XCubeNXT on the ground and do not step on the system to prevent any 
potential damages.

 

11.

 

Make sure the voltage is correct in the location where the XCubeNXT is installed. Contact the 
distributor or the local power supply company for the information.

 

12.

 

Do not place any object on the power cord.

 

13.

 

Do not attempt to repair the XCubeNXT in any occasions. Improper disassembly of the product 
may  expose  the  users  to  electric  shock  or  other  risks.  For  any  inquiries,  please  contact  the 
distributor.

 

14.

 

To remove  all  electrical current from  the  device, ensure  that  all  power  cords  are  disconnected 
from the power source.

 

15.

 

The XCubeNXT should only be installed in restricted access location such as in the server room 
and maintained by the qualified service person. The server room is locked by key or keycard, or 
other means of security access and only a qualified service person is allowed to enter the server 
room.

 

Содержание XCubeNXT XN8012D






































































Отзывы: