QNAP TS-1270U-RP Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 83

background image

27

Chapter 5.

Upgrade Memory on QNAP Turbo NAS (RAM Module
Installation)

Warning:



The following instructions should only be performed by an authorized and trained
technician.



Strictly adhere to the instructions to install a RAM module on the NAS. Failure to do
so could result in injury to human body or death.

QNAP provides 1GB/2GB DDR3 RAM module (optional purchase) for users to upgrade the
memory of Turbo NAS. Follow the steps below to install an extra memory module on the
NAS to upgrade the memory.

5.1

TS-x59 Pro II series (4/5/6-bay), TS-x69 series (2/4/5/6/8-bay)

Follow the steps below to install a RAM module on the NAS.

1.

Turn off the NAS. Disconnect the power adaptor, network cable(s), and any other
connectors or cables from the NAS.

2.

Before installing the memory module, put on an antistatic wrist strap to prevent
electrostatic discharge. The crocodile clip should be connected to the ground.

3.

Loosen the three screws on the rear of the NAS.

«
...
25
26
27
28
29
...
»

Содержание TS-1270U-RP




















































































Отзывы:

Нет отзывов

Похожие инструкции для TS-1270U-RP

Бренд: Vanguard Страницы: 121

ROADRECORDER 8000

Бренд: Safety Vision Страницы: 40

Бренд: D-Link Страницы: 176

Бренд: NEC Страницы: 6

MediaStream ConnectPlus 1000

Бренд: Avid Technology Страницы: 74

Бренд: NETGEAR Страницы: 2

Бренд: Aztech Страницы: 2

Бренд: Qixiang Technology Страницы: 16

Бренд: M86 Security Страницы: 309

Бренд: axing Страницы: 52

Media Board D/120JCT-LS-EW

Бренд: Dialogic Страницы: 2

CNPS11X Extreme

Бренд: ZALMAN Страницы: 12

Бренд: AXIOMTEK Страницы: 2

PowerMatch ESPLink

Бренд: Bose Страницы: 2

Бренд: XAVI Technologies Corp. Страницы: 63

Бренд: Accusys Страницы: 34

Бренд: Icy Box Страницы: 2

Бренд: LevelOne Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды