Qimarox PRORUNNER mk9 Скачать руководство пользователя страница 6

Страница: 6 / 61

About this manual

UM-PRORUNNER_mk9-2.0-EN

1.4

Symbols used in the manual

The following symbols are used in this manual.

1.5

Terminology list

The table below explains common terms used by Qimarox for the machine.

1.6

Further support and information

Qimarox can supply additional expertise and support services, for:

•

Training

•

Global support

•

Service contracts

For more information please contact Qimarox.

WARNING

Risk of serious injury to the user or damage to the machine if the instructions
are not accurately followed.

Note

To provide additional information to the user about a task or issue.

Term

Definition

machine

The PRORUNNER mk9.

product

Products transported by the machine.

carrier

The component on which a conveyor can be mounted or which carries the
product.

feeding conveyor

The conveyor that delivers products to the machine. The feeding conveyor
is not part of the machine.

discharge conveyor

The conveyor that discharges products from the machine. The discharge
conveyor is not part of the machine.

fenced area

Area around the machine that unauthorised personnel cannot enter for
safety reasons.

Содержание PRORUNNER mk9






























































Результаты поиска

Содержание PRORUNNER mk9

Отзывы:

Бренды по названию

Популярные бренды

Qimarox PRORUNNER mk9, Руководство пользователя

Результаты поиска

Содержание PRORUNNER mk9

Отзывы:

Бренды по названию

Популярные бренды