manualshive.com logo in svg

Qimarox PRORUNNER mk9, Руководство пользователя

Поделиться
Скачать
Qimarox PRORUNNER mk9 Скачать руководство пользователя страница 22

Description

22

UM-PRORUNNER_mk9-2.0-EN

4.6

Specifications

The information below, the machine layout drawing, the specification sheet and the 
identification plate give the specifications for the transportation of products.

4.6.1

Product transport specifications

Data concerning product type, dimensions, stability and weights must always be verified 
with Qimarox.

When permitted weight and distance deviate from the specifications in the machine layout 
drawing, the machine must be adjusted to accommodate this. These type of adjustments 
may only carried out by Qimarox or after written permission from Qimarox has been 
obtained.

If Qimarox does not supply the product conveyor, the weight of the applied conveyor 
needs to be checked by Qimarox to determine the correct drive on the vertical movement.

4.6.2

Environmental specifications

The surrounding area of the machine must comply to the following specifications:

/i

When the specifications for the surrounding area deviate from the table above, the 
machine must be adjusted to this. Such adjustments shall always be carried out by 
Qimarox or after permission from Qimarox.

4.6.3

Electrical specifications

See the type plate. Refer to section 

2.1

 and the electrical circuit diagrams.

Motor

The motor can be connected directly or through an operating switch in the main switch 
box. The machine must be controlled with a frequency inverter to ensure a smooth start 
and stop movement and to reduce speed.

The motor safety relays must meet EN-IEC 60204-1 specifications. The setting range 
depends on the motor specifications.

Property

Description

General

Covered and normally clean for operation. There must be suffi-
cient space around the machine for carrying out maintenance 
and other activities on the machine.

Relative air humidity

Maximum 80%.

Temperature

B5°C (41 F) and 40°C (104 F).

Floor

Even. The floor load is given in the machine layout drawing and 
specification sheet.

Required height

Refer to the machine layout drawing and specification sheet.

Compressed air

Between 5 bar and 7 bar in accordance with ISO 85731:2010 
[7:4:4]

Содержание PRORUNNER mk9






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды