manualshive.com logo in svg

Qimarox PRORUNNER mk9, Руководство пользователя

Поделиться
Скачать
Qimarox PRORUNNER mk9 Скачать руководство пользователя страница 10

General

10

UM-PRORUNNER_mk9-2.0-EN

2.4

Liability

Qimarox believes to the best of its knowledge that the information in this user manual is 
accurate. In the event that technical or typographical errors exist, Qimarox reserves the 
right to make changes to subsequent editions of this user manual without prior notice to 
holders of this edition. The reader should consult Qimarox if errors are suspected. In no 
event shall Qimarox be liable for any damages arising out of or related to this user manual 
or the information contained in it. Except as specified herein, Qimarox makes no 
warranties, express or implied, and expressly disclaims any warranty of non-infringement, 
merchantability or fitness for a particular purpose. Customer’s right to recover damages 
caused by fault or negligence on the part of Qimarox shall be limited to the amount paid to 
Qimarox by the customer. Qimarox shall not be liable for damages resulting from loss of 
data, profits, use of products, or incidental or consequential damages, even if advised of 
the possibility thereof. This limitation of liability of Qimarox will apply regardless of the form 
of action, whether in contract or tort, including negligence. Any action against Qimarox 
must be brought within one (1) year after that cause of action accrues.

Qimarox is not liable for damages, accidents, unsafe conditions, defects, malfunctions, or 
service failures caused by the following:

•

Owner’s or user’s failure to follow Qimarox’s installation, operation and maintenance 
instructions, including but not limited to neglecting warnings or regulations as shown 
on the machine or in this manual.

•

Usage of the machine for other applications, or under other circumstances than 
indicated in this user manual. This includes abuse, misuse or negligent acts.

•

Modifications of any kind to the machine. This includes the replacement of parts with 
parts that are not specified in this manual.

•

Insufficient or improper maintenance.

2.5

CE Declaration of Conformity

For the CE declaration of conformity, refer to the specification sheet.

Содержание PRORUNNER mk9






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды