Qiagen PyroMark Q24 MDx страница 7 Скачать руководство пользователя

Страница: 7 / 104

Safety Information

PyroMark Q24 MDx User Manual 01/2016

1-1

Safety Information

Before using the PyroMark Q24 MDx, it is essential that you
read this user manual carefully and pay particular attention

to the safety information.  The instructions  and safety
information  in the user manual must be followed  to ensure
safe operation  of the system and to maintain  the system in a

safe condition.
The following types of safety information appear throughout
this manual.

WARNING

The term WARNING is used to inform you about situations

that could result in

personal injury

to you or other

persons.
Details about these circumstances are given in a box like

this one.

CAUTION

The term CAUTION is used to inform you about situations
that could result in

damage to the system

or other

equipment.
Details about these circumstances are given in a box like
this one.

The advice given in this manual is intended to supplement,

not supersede, the normal safety requirements prevailing in

the user’s country.

1.1

Proper use

WARNING

Risk of personal injury and material damage

Improper use of the PyroMark Q24 MDx may cause
personal injuries or damage to the system.

PyroMark Q24 MDx must only be operated by qualified
personnel who have been appropriately trained.
Servicing of the PyroMark Q24 MDx must only be

performed by QIAGEN Field Service Specialists.

Perform the maintenance as described in Section 6.

QIAGEN

charges for repairs that are required due to

incorrect maintenance.

Содержание PyroMark Q24 MDx









































































































Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Похожие инструкции для PyroMark Q24 MDx

Бренды по названию

Популярные бренды

Qiagen PyroMark Q24 MDx, Руководство пользователя

Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Похожие инструкции для PyroMark Q24 MDx

Бренды по названию

Популярные бренды