Qiagen PyroMark Q24 MDx Скачать руководство пользователя страница 45

Страница: 45 / 104

Operating Procedures

PyroMark Q24 MDx User Manual 01/2016

5-17

analysis by performing the function test (steps 4–6 in
Section 5.5.5).

PyroMark Q24 Cartridge compartments from above.

5.5

Processing a run on the PyroMark Q24

MDx Instrument

The lid of the PyroMark Q24 MDx Instrument must remain
closed during operation of the instrument. An audible

warning signal will alert you if the lid is opened when it is not
safe.

WARNING

Moving parts

To avoid contact with moving parts during operation of the
PyroMark Q24 MDx Instrument, the instrument must be
operated with the lid closed.

Do not remove the cover panels since there are no user-
serviceable parts inside. If there is a problem with the
PyroMark Q24 MDx Instrument, contact QIAGEN

Technical Services immediately.

WARNING

Sharp needles

Do not touch the sharp needles at the bottom of the

reagent cartridge. Handle the needles with care. Small
particles and fibers may obstruct the needles.

Содержание PyroMark Q24 MDx









































































































Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Qiagen PyroMark Q24 MDx, Руководство пользователя, Страница: 45 / 104

Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы: