Qiagen PyroMark Q24 MDx страница 39 Скачать руководство пользователя

Страница: 39 / 104

Operating Procedures

PyroMark Q24 MDx User Manual 01/2016

5-11

Note

: Sepharose beads sediment quickly and capturing

of beads must take place immediately once agitation is

complete.

Note

: During immobilization, prepare the vacuum

workstation for the sample preparation (steps 1–8 in

Section 5.3.4).

5.3.4

Separation of DNA strands and release of
samples into the PyroMark Q24 Plate

WARNING

Hazardous chemicals

The Denaturation Solution used with the vacuum
workstation contains sodium hydroxide, which is irritating

to eyes and skin.
Always wear safety glasses, gloves, and a lab coat.
The responsible body (e.g., laboratory manager) must take

the necessary precautions to ensure that the surrounding
workplace is safe and that the operators are not exposed

to hazardous  levels of toxic substances  (chemical or
biological)  as defined in the applicable Material Safety
Data  Sheets (MSDSs) or OSHA,* ACGIH,

†

or COSHH

‡

documents.  For more information,  visit
www.qiagen.com/support/msds.aspx.
Venting for fumes and disposal  of wastes must be in

accordance with all national, state, and local health and
safety regulations and laws.

* OSHA: Occupational Safety and Health Administration (United States of America).

†

ACGIH: American Conference of Government Industrial Hygienists (United States of America).

‡

COSHH: Control of Substances Hazardous to Health (United Kingdom).

Things to do before starting

Prewarm one of the supplied PyroMark Q24 Plate Holders to

be used in Section 5.3.5 by placing it (without a plate) on a
heating block at 80°C.

Procedure

Ensure that the PyroMark Q24 MDx Vacuum Workstation
has been assembled correctly and securely.

Содержание PyroMark Q24 MDx









































































































Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Похожие инструкции для PyroMark Q24 MDx

Бренды по названию

Популярные бренды

Qiagen PyroMark Q24 MDx, Руководство пользователя

Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Похожие инструкции для PyroMark Q24 MDx

Бренды по названию

Популярные бренды