Quick Start Guide
www.Q5X.com 1-519-675-6999 info@Q5X.com
PREPARE:
Handheld MicCommander Remote Control
•
Remove the rubber cover to access the battery
chamber.
•
Install 2 AA batteries. Lithium is recommended for best
performance. Alkaline or Ni-MH are acceptable when
battery type is changed in the device configuration
menu.
•
Replace the rubber cover and install the antenna on the
top.
•
NEVER power the unit without the antenna in place.
•
Turn on the unit by pressing the power button on the
top or by plugging the USB cable.
•
The MicCommander will automatically shut off after
two minutes.
PREPARE:
QT-AD10 Transmitter
•
Bring the transmitter out of storage mode (minimal
battery draw) and into standby mode (detectable but the
UHF radio is off) using either method below:
•
Hold the ON/OFF button until the flashes
change from rapid to slow, or
•
Plug and unplug a powered charging cable into
the side of the transmitter.
•
Connect the microphone by pushing the mic connector
ends together.
PAIR:
MicCommander and Transmitter
•
The screen on the MicCommander displays the serial
number of paired transmitters. The serial number is on
the transmitter antenna or back.
•
If the desired transmitter is not listed, press the <MENU>
button to either scan for nearby transmitters or manually
add the serial number. Use the arrow buttons to navigate
the menu.
o
Scan: Press <ENTER> to scan. Use the down arrow to
select the transmitter. Use the side arrows to
review information about the transmitter. Press
<ENTER> to toggle the selection “x”. Press <MENU>
to access additional search functionality. Press
<Back> to accept the addition of a transmitter to the
list.
o
Add: Use the down arrow to select “Add” and press
<ENTER>. Use the navigation arrows to enter the
serial number. Hold the arrow key for rapid scroll.
Press <ENTER> to save.
•
Select the desired transmitter and press <ENTER> to go
to the transmitter menu.
Transmitters: 1 Power
20678 OFF
Scan
Remove
Remove ALL
Link
Add
This Quick Start Guide is an overview. Users are asked to
review the manual for detailed instructions.
The carrying pouch contains two parts.
•
Handheld MicCommander remote control (QG-H2)
•
Antenna
Users also need:
•
Q5X Digital transmitter
•
Microphone with special Lemo connector
•
Shure Axient Digital receiver
•
2 AA batteries
Visit www.Q5X.com/support to:
•
update the firmware
•
register the warranty
•
download the manuals
Quick Start Guide part number 55-0175
ADJUST
:
Set the functions in the two transmitter menus of
the MicCommander. Screen one includes: frequency, power
on/off, battery level, mic mute/live and mic offset. To access
screen two, navigate to NEXT> and press <ENTER> to adjust
transmitter name, group, RF power, 2.4GHz channel, storage
and reboot.
•
Frequency: Highlight the frequency and press <ENTER>.
Use the directional arrows to choose the desired
frequency. Hold the arrow for rapid scroll. Press <ENTER>.
•
Mic-offset: If using a single transmitter, set Offset to 0 dB.
If there is an audible difference in the sound level
between multiple transmitters, navigate to the Offset
menu (Audio
>
Offset) in the transmitter to increase or
decrease the Offset in real time to match the audio levels.
•
RF Power: Select between 2, 10 and 20mW. A lower
power level will conserve battery life.
•
Storage: Navigate to NEXT> and <ENTER>. Use the down
arrow to go to STORAGE and press <ENTER>. Navigate to
highlight CONTINUE on the warning screen and <ENTER>.
Frequency: 536.500MHz
Power: OFF ON OFF
Battery: 74%
Mic: OFF MUTE LIVE
Mic-offset: 0dB
NEXT>
25140:QT-AD10
x
M:0
Name: QT-AD10 M:0
Group: 0
RF Power: 10 mW
2.4 GHz Ch: 25
<BACK STORAGE REBOOT
QT-AD10
Handheld MicCommander™