Python 1000 ESP страница 26 Скачать руководство пользователя

Страница: 26 / 40

system features learn routine

The System Features Learn Routine™ dictates how the unit operates. Due to the number of steps, they have been

broken up into two menus. It is possible to access and change any of the feature settings using the

Valet®/Program switch. However, this process can be greatly simplified by using the optional DEI Bitwriter or

Personal Computer Interface, P/N 996T. Any of the settings can be changed and then assigned to a particular

transmitter, up to four, a feature called Owner Recognition. Each time that particular transmitter is used to disarm

the system, the assigned feature settings will be recalled. Owner Recognition is only possible when programming

the unit via the 996T or the 998T DEI Bitwriter.

Using the optional DEI Bitwriter or PC Interface, the learn routine may be locked. Make sure the learn routine is

unlocked before programming features. If the siren generates one long chirp when attempting to program the

unit, the learn routine is locked and must be unlocked using the DEI Bitwriter or PC before proceeding.

Open a door:

(The H1/5 GREEN wire or the H1/7 VIOLET wire must be connected.)

Ignition:

Turn the ignition on, then back off: (The H1/9 YELLOW wire must be connected.)

Select a menu:

Press and HOLD the Valet®/Program button: (The Valet®/Program button

must be plugged into the blue port.) After three seconds the siren will chirp once indicat-

ing entry to the Basic Features Menu #1. If this is the menu you wish to access, release

the button and go on to step 4. If the button is not released, you will jump to the

Advanced Features Menu #2 and the siren will chirp twice. Once you have selected the

desired menu, release the Valet®/Program button and then go to step four.

Select a feature:

Press and release the Valet®/Program button the number of times corre-

sponding to the step you wish to change. For example, to access the third feature, press

and release three times. Then press the button once more and HOLD it. The siren will chirp

the number of times equal to the step you have accessed.

Program the feature:

While holding the Valet®/Program button, you can toggle the feature

on and off using the remote transmitter. Pressing

will select the one chirp or default

setting. Pressing

will select the two chirp setting. (See

Transmitter/Receiver Learn

Routin

e section of this guide.)

Содержание 1000 ESP









































Результаты поиска

Содержание 1000 ESP

Отзывы:

Похожие инструкции для 1000 ESP

Бренды по названию

Популярные бренды

Python 1000 ESP, Руководство по установке

Результаты поиска

Содержание 1000 ESP

Отзывы:

Похожие инструкции для 1000 ESP

Бренды по названию

Популярные бренды