background image

                                                                                                                           DECIBELL 

Page: 18                                                                                                                 RINS040-5 

8. TECHNICAL SPECIFICATIONS 

OPERATING VOLTAGE 

SIREN AND STROBE OUTPUT 

10 – 16Vdc. (13.8V Nominal) 

Maximum peak:

 

118dBA @ 1m (85dBA Spain)

 

Reverse polarity protected 

Flash rate:

 

120/min typical

 

 

Tube size:

 

3 Watt

 

CURRENT CONSUMPTION 

 

Stand by (alt. flashing):

 

30mA typical

  

 

                            

(+10mA for backup battery) BACKUP BATTERY 

Strobe only:

 

165mA typical

 

280mAh 7.2 V NiCad (included) 

Siren only:

 

245mA typical

 

30 min continuous use (Siren and Strobe) 

Siren and Strobe:

 

440mA typical

 

 

 

SIREN CUT OFF TIMER 

 

Test:

 

 5 seconds

 

DIMENSIONS & WEIGHT 

Normal: 

 15 minutes

 

Dimensions:  

325mm x 180mm x 75mm

 

 

Weight: 

1.4kg

 

ENVIRONMENT 

 

Operating Temperature:

  

-30

˚

 to 50

˚

C (-22

˚

 to 122

˚

F)

 

 

Storage Temperature: 
 

-40

˚

 to 60

˚

C (-40

˚

 to 140

˚

F)

 

 

TAMPER PROTECTION 

Activation from front or back and power supply cut off 
 

INPUT ACTUATION 

Strobe and Siren, switched negative or positive 
 
 
 
 

This product is suitable for use in systems designed to 

comply with PD 6662:2004 at Security Grade 3 and Environmental Class 4.

EN50131-1

Security Grade 3
Env

4

 

 

Содержание DECIBELL

























Отзывы: