PVI Industries TEMPTRAC Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 30

PVI Industries TEMPTRAC Скачать руководство пользователя страница 2

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST

Page 2 of 30

PV7069-T 03/17
Part number 129209

OVERVIEW OF INTERFACE METHODS:

This document is a quick reference for connecting the TempTrac water heater / boiler control to a Building
Automation System (BAS). Direct connection via MODBUS RTU or using a gateway to interface to
protocols other than MODBUS RTU are the methods covered in this manual.

BAS to Heaters direct, using MODBUS RTU:

Building Automation System (BAS) connecting directly to water heaters using MODBUS RTU twisted pair
wire. (Wiring is RS-485 physical layer.)

BAS to heaters using a Protocol Gateway:

Building Automation System (BAS) connecting to a PVI gateway. This can provide interface to BACNET
MSTP, BACNET IP, LONWORKS, and MODBUS TCP.
(Wiring from gateway to heaters is RS-485 physical layer. Wiring from BAS to gateway will depend on
Protocol.)

BAS to heaters using discrete connections:

This is simply control of the heater using the external ENABLE/DISABLE contacts, remote equipment
contacts and the alarm contacts. See wiring diagram of equipment for details.

Other equipment

GATEWAY

PVI WATER HEATERS

BAS

Other equipment

PVI WATER HEATERS

BAS

«
1
2
3
4
...
»

Содержание TEMPTRAC































Отзывы:

Нет отзывов