PureTools PT-PSW-41H Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 28

background image

User Manual

11

5.

RS232 Control

Connect the control device (PC) to the RS232 port of PT-PSW-41H, The PT-PSW-41H can be

controlled by sending RS232 commands via RS232 control software installed in the PC.

5.1

RS232 Control Software



Installation:

Copy the control software file to the computer connected with PT-PSW-41H.



Uninstallation:

Delete all the control software files in the corresponding file path.



Basic Settings:

First connect PT-PSW-41H with all needed input and output devices, then connect it with a

computer which is installed with RS232 control software. Finally, double-click the software

icon to run this software.

Here we take the software

CommWatch.exe

as example. The icon is shown as below:

«
...
14
15
16
17
18
...
»

Содержание PT-PSW-41H





























Отзывы:

Нет отзывов

Похожие инструкции для PT-PSW-41H

Бренд: Dataprobe Страницы: 31

Бренд: IBM Страницы: 13

Flex System EN2092

Бренд: IBM Страницы: 2

Бренд: Jabra Страницы: 4

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Бренд: Jabra Страницы: 2

Бренд: Pakedge Страницы: 24

Бренд: Aastra Страницы: 52

Бренд: N-Tron Страницы: 169

GlobeCaster STUDIO 4000

Бренд: Global Streams Страницы: 144

TNM4000-TP36FF4X16G24P

Бренд: MRD Страницы: 38

Бренд: nedis Страницы: 24

Бренд: NETGEAR Страницы: 8

Бренд: Kramer Страницы: 2

Бренд: Digitus Страницы: 10

Бренд: The Siemon Company Страницы: 2

Бренд: Grandbeing Страницы: 27

Бренд: Kramer Страницы: 10

AT-HDDVI1616-AM

Бренд: Atlona Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды