PureTools PT-PSW-21C Скачать руководство пользователя страница 23

Страница: 23 / 36

User Manual

PT-PSW-21C

6.2.2

Source Switching

Command

Function

Feedback Example

#SET_AV H

Switch to HDMI input.

@AV H

#SET_AV C

Switch to USB-C input.

@AV C

#GET_AV

Get the current input source.

@AV H

@AV C

#SET_AUTO_SWITCH 1

Enable auto switching mode.

@AUTO_SWITCH 1

#SET_AUTO_SWITCH 0

Disable auto switching mode.

@AUTO_SWITCH 0

#GET_AUTO_SWITCH

Get the auto switching status.

@AUTO_SWITCH 1

@AUTO_SWITCH 0

6.2.3

User-defined EDID

There are five EDID values can be customized by sending the below command.

Command

Function & Operation

#UPLOAD_USER_EDID
[X].

X =1~5, represents the EDID, its DIP switch status shows as below:

DIP Switch Status

1011

1100

1101

1110

1111

Operation:

Step 1:

Prepare the EDID file (.bin).

Step 2:

Set the 4-pin DIP switch

status, for example: “1011”.

Step 3:

Send the command “

#UPLOAD_USER_EDID 1.

”, and the feedback

is “

@USER_EDID 1 READY

PLEASE SEND EDID DATA IN 10S

”

Step 4:

Send the

EDID file (.bin). If successfully upload, the feedback is:

“

”.

Содержание PT-PSW-21C




































Результаты поиска

Содержание PT-PSW-21C

Отзывы:

Похожие инструкции для PT-PSW-21C

Бренды по названию

Популярные бренды

PureTools PT-PSW-21C, Руководство пользователя

Результаты поиска

Содержание PT-PSW-21C

Отзывы:

Похожие инструкции для PT-PSW-21C

Бренды по названию

Популярные бренды