PureTools PT-PMS-62S Скачать руководство пользователя страница 55

Страница: 55 / 64

User Manual

PT-PMS-62S

8.2.12

Trigger Feedback Command Setting



Command

Function

Command Example

/+[Y]/[B]:******.



xxxxxx: Feedback command (ASCII
characters).



Y: Represents the RS232 port.

Y=A: When power on system,
receive the feedback command
from the RS232 port of switcher.

Y=B: When power on system,
receive the feedback command
from the RS232 port of HDBaseT
receiver.

Y=a: When power off system,
receive the feedback command
from the RS232 port of switcher.

Y=b: When power off system,
receive the feedback command
from the RS232 port of HDBaseT
receiver.



B: Represents the baud rate of
third-party device.

Baud Rate

2400

4800

9600

19200

38400

57600

115200

/+A/3: Play ON 123.

When power on system, receive
the feedback command “Play ON
123.” from the RS232 port of
switcher.

%9951.

Report the feedback command which
is sent by the RS232 port of the
switcher while power on system.

Port 1: D_ON when PWON

Содержание PT-PMS-62S
































































Результаты поиска

Содержание PT-PMS-62S

Отзывы:

Похожие инструкции для PT-PMS-62S

Бренды по названию

Популярные бренды

PureTools PT-PMS-62S, Руководство пользователя

Результаты поиска

Содержание PT-PMS-62S

Отзывы:

Похожие инструкции для PT-PMS-62S

Бренды по названию

Популярные бренды