PureTools PT-C-HDCEC Скачать руководство пользователя страница 20

Страница: 20 / 28

User Manual

PT-C-HDCEC

6.1.4

RS232 Control Setting

Command

Function

Feedback Example

R[X]:XXX

When detecting a triggering signal,
automatically send ASCII command XXX
to the third-party device (e.g. Projector)
whose baud rate is X.

Baud Rate

2400

4800

9600

19200

38400

57600

115200

R3:123abc

Send the ASCII command
“123abc” to the third-party
whose baud rate is 9600.

RS232ON/-[X]:XXX

When detecting a triggering signal,
automatically send HEX command XXX
to the third-party device (e.g. Projector)
whose baud rate is X.

RS232ON/-3:30 31 32

Send the HEX command “30 31
32” to the third-party whose
baud rate is 9600.

RS[X]:XXX

When not detecting any triggering
signal, automatically send ASCII
command XXX to the third-party device
(e.g. Projector) whose baud rate is X.

RS3:123abc

Send the ASCII command
“123abc” to the third-party
whose baud rate is 9600.

RS232OFF/-[X]:XXX

When not detecting any triggering
signal, automatically send HEX
command XXX to the third-party device
(e.g. Projector) whose baud rate is X.

RS232OFF/-3:30 31 32

Send the HEX command “30 31
32” to the third-party whose
baud rate is 9600.

[X]:XXX

Set the user-defined ASCII command to
send to the third-party device (e.g.
projector) whose baud rate is X.

RS23:123abc

Send the user-defined command
“123abc” to the third-party
whose baud rate is 9600.

Содержание PT-C-HDCEC




























Результаты поиска

Содержание PT-C-HDCEC

Отзывы:

Похожие инструкции для PT-C-HDCEC

Бренды по названию

Популярные бренды

PureTools PT-C-HDCEC, Руководство пользователя

Результаты поиска

Содержание PT-C-HDCEC

Отзывы:

Похожие инструкции для PT-C-HDCEC

Бренды по названию

Популярные бренды