Puretec Sparq S4 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 20

Puretec Sparq S4 Скачать руководство пользователя страница 3

3

Copyright © Puretec Pty Ltd 2021

Puretec Sparq S4 User Guide

Introduction

Puretec Customer Service

Thank you for purchasing a Puretec Sparq S4 Drinking Water Appliance. The Sparq S4 is
a proven performer manufactured from only quality materials and components. It will
give years of reliability and trouble-free operation if maintained properly.

Caution:

Do not use with water that is microbiologically unsafe or without adequate

disinfection before or after the system.

The Puretec Sparq S4 is designed for metropolitan supply water only.

Flush the system for 5 minutes or more, after any period of non-use, more than 2 weeks.

Note:

Where maximum line pressure exceeds 500 kPa, the supplied multivalve

(pressure limiting valve) must be installed to comply with Australian Plumbing

Standards.

PRODUCT INFORMATION

Model Number:

SPARQ-S4

Serial / Batch Number:

(Refer to label on the rear of the unit)

Purchased From:

Date of Installation:

Installer / Plumber Details:

Installation Record

For future reference, fill in the following data:

All installation and service work should be completed by qualified tradespeople. Faulty
operation due to unqualified persons will result in voided warranty.

All plumbing must comply with AS 3500.1 and AS3500.2.15.

«
1
2
3
4
5
...
»

Содержание Sparq S4





















Отзывы:

Нет отзывов