Mains Supply
ChromaZone(s)
mains cable
WARNING - THIS APPLIANCE MUST BE EARTHED
For safety we recommend the use of a Residual Current
Circuit Breaker. An RCCB MUST be used when powering
e.g. ChromaFixtures in wet environments.
Electronics On/Off Switch
Indicator Neon
Electronics Mains Fuse
- The
works correctly on any
mains voltage from 85-277 VAC, 50-60Hz, (self adjusting).
Power consumption: CZ6 - 100 Watts, CZ12 - 200 Watts
depending on the number of fixtures connected and their output
levels. Please see the table shown below for more information.
A
with locking IEC female connector attached is
supplied (not supplied with IP Zones). To unlock the IEC
connector, pull/side the red tab towards yourself then pull
connector out. The other end of the cable should be fitted with a
suitably approved and rated mains plug. Note: in some countries
it is a requirement that such a plug be fitted by a qualified
electrician.
with built in
.
: 5 Amp, HRC, 5x20mm.
Pulsar's Chroma Lighting Fixtures - ChromaStrips ,
C h r o m a T u b e s
,
C h r o m a P a n e l s
,
C A R 1 1 1
ChromaScapes
,
CBAT17
, ChromaBatten50
,
ChromaHearts , ChromaInGround , ChromaFlood50 ,
ChromaPoint , ChromaInGroundMR16SS , etc
ChromaFixtures Leaflet
ChromaZone Max Fixture
Loading Data
ChromaZone
,
(User Interface Module)
DMX D
M
X
CZ6/12
.
TM
T M
T M
T M
T M
T M
T M
TM
TM
TM
TM
TM
TM
., contain
state of the art, high brightness, high efficiency Red, Green and
Blue LEDs. These three primary colours can be mixed together
to make an incredible pallet of 16.7 million colours.
Please see the
for details of the
luminaires themselves and page 3 -
which will inform you of how many fixtures you may
put on the outputs of different ChromaZones.
The
has numerous chases and effects built in
making it possible to achieve fantastic effects without
programming. These internal effects can be selected via the UIM
on the lid of the unit in Stand Alone
mode or from a controller using a digital
( igital
ultiple )
signal.
When receiving a signal the
can operate in 3, 6, 9, 10, 36,
42 or 46 Channel Modes Please see the lid printing page for
details of these Operating Modes, how to select them, Channel
Listings, and further information.
Each ChromaFixture
requires a +24VDC supply and three 0 to
+10V control signals to control the level of Red, Green and Blue.
These control signals and the low voltage power are provided by
the CZ12 and CZ6 controllers which can drive up to 12 or 6
ChromaFixtures respectively.
ChromaZone12 200W - Mk2
TM
CZ12-200
ChromaZone6
100W - Compact
TM
CZ6-100C
ChromaPSU2
PSU
TM
CPSU2
Cable Colours
Green/Yellow =
Brown =
Blue =
Earth / Ground
Live / Phase / Hot
Neutral
ChromaFlex Grey 5 Core Multiway Cable
8075G
8075SUB
ChromaFlex Submersible 5 Core Cable
CZ12-200IP
ChromaZone12 200W - IP65
TM
Model
Outputs
Max Load
Control
50W
17W
CP300
MR16
Link
Point
Strip 25/X1
Strip X3
CZ12-200(IP)
12
200W
DMX
4
12
48
60
96
96
14.4 mts
4.8 mts
CZ6-100C
6
100W
DMX
2
6
24
30
48
48
7.2 mts
2.4 mts
CPSU2
2
35W
0-10V
0
2
8
10
16
16
2.4 mts
0.6 mts
The CBAT50, CFLD50 and CIG50 require up to 50 Mains Watts
each which will reduce the number of products you can use per
ChromaZone e.g. 4 x CFLD50 = 200W. Do not exceed the max
mains wattage of the zone.
NB - Patents applied for. Trade Marks, Copyright, Registered
and Unregistered Design Rights apply on all Chroma
Products.
CHROMA
CHROMA
RANGE
ZONE
CHROMAZONE MAINS SUPPLY
GENERAL INFORMATION
Pulsar Light of Cambridge Limited
Tel:
Email:
Web:
, 3 Coldhams Business Park, Cambridge, CB1 3LH, England
44 (0)1223 403500
www.pulsarlight.com
7571 PSU12-200IP Instructions
