background image

PIM90.241

Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN

www.pulspower.com

9 / 17

All parameters are specified at 24V, 3.8A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.

9.

Lifetime Expectancy

The  Lifetime  expectancy  shown  in  the  table  indicates  the  minimum  operating  hours  (service  life)  and  is  determined  by
the lifetime expectancy of the built-in electrolytic capacitors. Lifetime expectancy is specified in operational hours and is
calculated according to the capacitor’s manufacturer specification.

Please note: The manufacturer of the electrolytic capacitors only guarantees a maximum life of up to 15 years (131 400h).
Any number exceeding this value is a calculated theoretical lifetime which can be used to compare devices.

AC 100V

AC 120V

AC 230V

Lifetime expectancy

39 000h

64 000h

102 000h

At 24V, 3.8A and 40°C

260 000h

292 000h

309 000h

At 24V, 1.9A and 40°C

91 000h

147 000h

287 000h

At 24V, 3.8A and 25°C

640 000h

720 000h

815 000h

At 24V, 1.9A and 25°C

10. MTBF

MTBF  stands  for  Mean  Time  Between  Failure,  which  is  calculated  according  to  statistical  device  failures,  and  indicates
reliability of a device. It is the statistical representation of the likelihood of a unit to fail and does not necessarily represent
the life of a product.

The MTBF figure is a statistical representation of the likelihood of a device to fail. A MTBF figure of e.g. 1 000 000h means
that statistically one unit will fail every 100 hours if 10 000 units are installed in the field. However, it cannot be determined
if the failed unit has been running for 50 000h or only for 100h.

For these types of units the MTTF (Mean Time TFailure) value is the same value as the MTBF value.

AC 100V

AC 120V

AC 230V

MTBF SN 29500, IEC 61709

1 174 000h

1 273 000h

1 507 000h

At 24V, 3.8A and 40°C

2 251 000h

2 406 000h

2 752 000h

At 24V, 3.8A and 25°C

MTBF MIL HDBK 217F

751 000h

760 000h

698 000h

At 24V, 3.8A and 40°C; Ground Benign GB40

1 085 000h

1 099 000h

1 018 000h

At 24V, 3.8A and 25°C; Ground Benign GB25

219 000h

224 000h

220 000h

At 24V, 3.8A and 40°C; Ground Fixed GF40

288 000h

294 000h

293 000h

At 24V, 3.8A and 25°C; Ground Fixed GF25

Содержание PIM90.241


















Отзывы: