Puls PIANO PIM60.241 Скачать руководство пользователя страница 9

PIM60.241

Feb. 2022 / Rev. 2.0 DS-PIM60.241-EN

www.pulspower.com

9 / 17

All parameters are specified at 24V, 2.5A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.

9.

Lifetime Expectancy

The  Lifetime  expectancy  shown  in  the  table  indicates  the  minimum  operating  hours  (service  life)  and  is  determined  by
the lifetime expectancy of the built-in electrolytic capacitors. Lifetime expectancy is specified in operational hours and is
calculated according to the capacitor’s manufacturer specification.

Please note: The manufacturer of the electrolytic capacitors only guarantees a maximum life of up to 15 years (131 400h).
Any number exceeding this value is a calculated theoretical lifetime which can be used to compare devices.

AC 100V

AC 120V

AC 230V

Lifetime expectancy

115 000h

131 000h

148 000h

At 24V, 2.5A and 40°C

260 000h

263 000h

263 000h

At 24V, 1.25A and 40°C

324 000h

370 000h

419 000h

At 24V, 2.5A and 25°C

734 000h

744 000h

744 000h

At 24V, 1.25A and 25°C

10. MTBF

MTBF  stands  for  Mean  Time  Between  Failure,  which  is  calculated  according  to  statistical  device  failures,  and  indicates
reliability of a device. It is the statistical representation of the likelihood of a unit to fail and does not necessarily represent
the life of a product.

The MTBF figure is a statistical representation of the likelihood of a device to fail. A MTBF figure of e.g. 1 000 000h means
that statistically one unit will fail every 100 hours if 10 000 units are installed in the field. However, it cannot be determined
if the failed unit has been running for 50 000h or only for 100h.

For these types of units the MTTF (Mean Time TFailure) value is the same value as the MTBF value.

AC 100V

AC 120V

AC 230V

MTBF SN 29500, IEC 61709

1 797 000h

1 858 000h

1 982 000h

At 24V, 2.5A and 40°C

3 093 000h

3 186 000h

3 378 000h

At 24V, 2.5A and 25°C

MTBF MIL HDBK 217F

868 000h

886 000h

803 000h

At 24V, 2.5A and 40°C; Ground Benign GB40

1 257 000h

1 278 000h

1 175 000h

At 24V, 2.5A and 25°C; Ground Benign GB25

247 000h

252 000h

247 000h

At 24V, 2.5A and 40°C; Ground Fixed GF40

325 000h

331 000h

328 000h

At 24V, 2.5A and 25°C; Ground Fixed GF25

Содержание PIANO PIM60.241


















Отзывы: