PT AMC131 Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 108

background image

Chapter 9: Agency Approvals

104

EN55022 Radiated and Conducted Emissions

EN300 386 Electromagnetic Compatibility (EMC)

EN55024 Immunity

EN61000-4-2

Electro-Static Discharge (ESD)

EN61000-4-3

Radiated Susceptibility

EN61000-4-4

Electrical Fast Transient Burst

EN61000-4-5

Surge Immunity

EN61000-4-6

Frequency Magnetic Fields

EN61000-4-11

Voltage Dips, Variations, and Short Interruptions

Safety

The product described in this manual meets the following safety regulations:

EN/IEC 60950

Safety Requirements for Information Technology Equipment

CB Scheme

CB Scheme Certificate and Report

UL60950

UL Recognized

FCC (USA) Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

Note: Modifications made to this device that are not approved by Performance Technologies,
Inc. may void the authority granted to the user by the FCC to operate this equipment.

«
...
102
103
104
105
106
...
»

Содержание AMC131













































































































Отзывы:

Нет отзывов

Похожие инструкции для AMC131

Бренд: JJ Cole Collections Страницы: 16

Бренд: JJ Cole Страницы: 13

DO CF19591-2EFA

Бренд: CARFACE Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды