Psion Teklogix OMNii HDK XT10 Скачать руководство пользователя | Manualshive

Страница: 81 / 192

background image

Chapter 5: Mechanical Considerations

Back Cover Modules and Devices

Psion Teklogix Omnii HDK User Manual

71

5.4.4

Back Cover Modules and Devices

This section describes the specifics of designing and mounting custom-made back covers
on Omnii.

Designing Back Cover Modules

To maintain proper protection against water and dust ingress, back cover modules must form a
tight seal with the main housing. A soft overmould around the perimeter of the opening creates a
seal with the attached back cover. The back cover module must be designed with a corresponding
hard ridge that presses into the overmould to form this seal. The 3D CAD model of any of the
supplied back covers can be used to obtain the required width, depth and shape of this ridge.

Table 5.9 Associated Files for Back Covers

Description

Filename

2D line drawings of the auto-range standard back cover with
locations of mounting points for the back cover and pistol grip

Back_Cover_Auto_Std_2D.dwg

Back_Cover_Auto_Std_2D.pdf

3D CAD models of the auto-range standard back cover

Back_Cover_Auto_Std_3D.igs

Back_Cover_Auto_Std_3D.stp

2D line drawings of the expansion back cover with locations of
mounting points for the back cover, pistol grip, end-cap and
pod expansion

Back_Cover_Expan_2D.dwg

Back_Cover_Expan_2D.pdf

3D CAD models of the expansion back cover, showing end-cap
and pod expansion openings with sealing overmoulds, and
keep-away areas for camera and speaker options

Back_Cover_Expan_3D.igs

Back_Cover_Expan_3D.stp

2D line drawings of the large standard back cover with loca-
tions of mounting points for the back cover and pistol grip

Back_Cover_Large_Std_2D.dwg

Back_Cover_Large_Std_2D.pdf

3D CAD models of the large standard back cover

Back_Cover_Large_Std_3D.igs

Back_Cover_Large_Std_3D.stp

Table 5.10 Required Fasteners

How Used

Quantity Part Number Screw Size Torque

(in-lb)

Bit

Pod Expansion to Expansion Back Cover

4

1005090

M3x5

5.0

T10

Back Cover to Main Housing (Back)

8

1004948

M3x6

5.0

T10

Back Cover to Main Housing (Front)

2

1004946

M2x8

2.5

T6

Inserts

2

1005273

M2x5

N/A

N/A

«
...
79
80
81
82
83
...
»

Содержание OMNii HDK XT10

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMNii HDK XT10

Бренд: Intermec Страницы: 11

Бренд: Datalogic Страницы: 59

Бренд: Datalogic Страницы: 68

Pocket LOOX C Series

Бренд: Fujitsu Siemens Computers Страницы: 61

Бренд: Epec Страницы: 48

Бренд: Mobile Crossing Страницы: 63

Бренд: Joinwit Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды