Psion Teklogix OMNii HDK XT10 Скачать руководство пользователя страница 43

Страница: 43 / 192

Chapter 4: Software

Serial (COM) Port Assignments

Psion Teklogix Omnii HDK User Manual

4.6

Serial (COM) Port Assignments

The default serial port assignments for Omnii are shown in the following table. Ports not listed
are unassigned.

Table 4.5 Default Omnii Serial (COM) Port Assignment

Serial

Port

Default Assignment

Comments

COM2:

GPS

This COM port is opened by applications that require GPS data.
This COM port may instead be opened by the GPS
intermediate driver.

COM5:

External USB-serial dongle External USB-to-serial adaptor dongle WA4015 can be plugged

into USB-A port on desktop dock and snap module.

COM6:

USB port replicator

RS-232 port on portable docking module.
RS-232 port on desktop docking station.
RS-232 port on vehicle cradle.
Internal USB-to-serial converter in the desktop dock XMOD
option, snap-module, and vehicle cradle.

COM7:

Reserved for future use.

COM8:

WWAN virtual serial port

WWAN not available on the Omnii XT10.

COM18

WWAN hardware (private) Reserved for internal use.

COM19

GPS hardware (private)

Reserved for internal use.

COM20

Bluetooth

hardware

(private)

Reserved for internal use.

COM24

GPS power (private)

Reserved for internal use.

COM30

Expansion UART1

COM31

Expansion UART2

COM32

Expansion UART3

COM33

Internal scanner port

Note: 1. The proper name for COM ports above COM9 is \$device\COMxx

(no “:” following the COM port number).
2. COM ports cannot be reassigned on the Omnii.
3.

Bluetooth

creates and destroys many virtual ports.

Содержание OMNii HDK XT10

































































































































































































Результаты поиска

Содержание OMNii HDK XT10

Отзывы:

Похожие инструкции для OMNii HDK XT10

Бренды по названию

Популярные бренды

Psion Teklogix OMNii HDK XT10, Руководство пользователя

Результаты поиска

Содержание OMNii HDK XT10

Отзывы:

Похожие инструкции для OMNii HDK XT10

Бренды по названию

Популярные бренды