Psion Teklogix OMNii HDK XT10 Скачать руководство пользователя | Manualshive

Страница: 127 / 192

background image

Chapter 8: EEPROM Specifications

Overview

Psion Teklogix Omnii HDK User Manual

117

8.1

Overview

This chapter describes and defines the content of the EEPROMs that are used to identify modules
attached to Omnii.

8.2

EEPROM Hardware

Theory of Operation

Expansion modules should be equipped with a Maxim DS2431 1-wire EEPROM to identify the
module and its properties to the system. This information is displayed to the user in the System
Properties Control Panel applet, and is used to load appropriate software drivers.
The required pull-ups for the operation of this EEPROM are included on the main logic board.
Due to the slow transfer speed of the EEPROMs, it is not recommended to use larger EEPROMs,
or to store larger amounts of information in them. Also, since the EEPROM data is read from the
SysCon (system controller), it is not recommended to use the EEPROM storage for any
operational functions beyond initial device setup at boot time. Accessing the EEPROM memory
during device operation will consume the SysCon processing time and may slow the system
down.

8.3

EEPROM Data Specification

The module EEPROM is used to identify the hardware and load appropriate software drivers. The
identity will be displayed to the user in the System Properties panel of the System control panel,
and will be accessible to drivers and applications.
This section describes the fields of the EEPROM which are predefined for this purpose.
Manufacturers are free to use unused areas of the EEPROM for their own configuration purposes.

All modules will share the common EEPROM fields below, and each module type may have
specific additional fields.

8.3.1

Common EEPROM Fields

Unused fields/bytes have the value 0xFF. If the specified fields are set to 0xFF, "Unknown" is
displayed in the corresponding entry in the System Properties Control Panel.
Data in a text field must start at the first byte of the field. If the data does not fill the text field, the
first occurrence of byte 0xFF or 0x00 terminates the text string.

Note: The expansion module one-wire EEPROM may not be writable at all times during device

operation and therefore should not be relied on for use after boot time.

«
...
125
126
127
128
129
...
»

Содержание OMNii HDK XT10

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMNii HDK XT10

Бренд: M3 Mobile Страницы: 45

Бренд: Bartec Страницы: 18

Бренд: Pepper Computer Страницы: 16

Pocket LOOX 600

Бренд: Siemens Страницы: 11

Бренд: Datalogic Страницы: 59

Бренд: Datalogic Страницы: 68

Бренд: HandHeld Страницы: 77

Бренд: Falcon Страницы: 68

Бренд: Wavenet Страницы: 98

AMXU GPS EXPANSION POD

Бренд: Juniper Страницы: 12

Бренд: Juniper Страницы: 15

Бренд: Juniper Страницы: 52

Бренд: Juniper Страницы: 94

Бренд: Juniper Страницы: 122

Ultra-Rubbed Field PC

Бренд: Juniper Страницы: 176

Бренд: GRAYHILL Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды