manualshive.com logo in svg

PS Engineering PAC45A, Инструкция по установке и эксплуатации, Страница: 14 / 50

Поделиться
Скачать
PS Engineering PAC45A Скачать руководство пользователя страница 14

PS Engineering 

PAC45J Audio Selector Panel and Intercom System 

Installation and Operator’s Manual 

 

200-045-2000 

Page 2-5 

November 2020 

When enabled, P452-39 is a low-level (10KΩ, 2Vpp max) speaker output with the radio audio selected on 
the 

Observer 1

 CTL45J Control Panel.  

Low Level audio can be amplified to 4Ω, 10W speaker output with a PS Engineering PSA210, Dual Channel 
speaker amplifier, P/N 050-230-0000 (call PS Engineering for pricing). See §2.7.14 for information on se-
lecting CVR or low-level speaker outputs.  

Speaker output volume control is with the master radio volume, left inner knob.  

2.4.8 

Audio Alerts 

The PAC45J contains an independent audio alerting systems that will play up to 9 messages that can be stored 
by the user (see §

3.11.1

). Factory stored default audio is shown below. 

The alert system has a power input (P451-41) that will  keep the systems operable if the PAC45J systems 
power source is removed. Alert audio is provided in Fail-safe when power is on P451-62. 

Alert Input 

Input Pins 

Alert Audio 

1 

P453 – 10  

“Master Caution” 

2 

P453 – 11  

“Alert” 

3 

P453 – 12  

Chime 

4 

P453 – 13 

1000 Hz tone 

5 

P453 – 14 

Doorbell Chime 

6 

P453 – 19 

Ring Tone 

7 

P453 – 20 

“Timer at Zero” 

8 

P453 – 21 

“Intercom Call” 

9 

P453 – 22 

“ Check Engine Instruments” 

Alert Power 

P451 – 41  

 

Remote 

Acknowledge 

P453 – 23 

 

The alert triggers can be configured to be Active High (>4.5 VDC) or Active Low (<0.5 VDC), and trigger 
at the leading-edge transition or by the voltage level.  See §

2.5.3

 for configuration options.  

Alerts  with  edge  triggers  will  play  continuously  until  the  Acknowledge  button  (ACK)  is  pressed  (remote 
ACK P454-23 grounded).  

Alerts with level trigger will play continuously until the Acknowledge button (ACK) is pressed (remote ACK 
P454-23 grounded), or the input level reverts.  

When power is applied to the alerts and not the PAC45J audio controller, it will play the message continu-
ously until the remote acknowledge is selected. 

The volume level of the alerts is adjustable with potentiometer 13 on the side of the HUB45AR (See 

§2.7.2

) 

Audio alerts are inhibited for the first 30 seconds after HUB power up to reduce nuisance triggers.  

2.4.9 

CTL45J wiring 

The PAC45J supports up to 4 CTL45J control heads. Three can be connected to the rear connectors, and the 
fourth to J455. For convenience, either the pilot or observer #2 can be connected to J454 (See §2.7.14). 

CTL45J can be configured for 28VDC or 5 VDC dimming.  

Set J5 switches to: off/off/off/off/off/off for 28 VDC Lighting.  

Set J5 switches to: off/off/off/off/on/off for 14 VDC Lighting  

Set J5 switches to: off/off/off/off/on/on for 5 VDC Lighting.  

 

Содержание PAC45A



















































Отзывы:

Нет отзывов