PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 52

Страница: 52 / 176

3-2

VIBXPER

T II 05.2012

What is a measurement task?

To carry out a measurement, VIBXPERT requires information on the

type of measurement quantity*, the sensor being used and, if neces-

sary, data for the evaluation of the result. Information as to whether

the RPM must be recorded with each measurement is also required.

This data set is designated as a 'measurement task' and forms the basis

for each measurement with VIBXPERT.
To simplify the preparation of a 'multimode' measurement and to save

the user from having to enter the required data, VIBXPERT already

contains a comprehensive collection of predefined knowledge-based

measurement tasks. The user is only allowed to change the transducer

and to alter the measurement channel in these measurement tasks. If

extensive changes to the measurement parameters are required, it is

better to create a new measurement task.
In the 'Route' and 'Machine Template' operating modes, VIB XPERT

receives the measurement tasks directly from the OMNITREND PC

software. Only a few of the measurement parameters here can be

changed (transducer, measurement channel, RPM entry).
The following overview shows the structure of a measurement task in

VIBXPERT:

*Measurement quantity:
Vibration acceleration,
Vibration velocity
Vibration displacement as overall value,
time signal or spectrum respectively
Shock pulse,
Temperature,
RPM,
...

The measurement tasks are sorted according to measurement quan-

tity* and assigned a measurement icon in the selection screen. If you

are in the 'Multimode' operating mode for example, all measurement

tasks of the 'Vibration velocity - overall value' measurement quantity

appear under the icon shown above. The letters 'a', 'v', and 'd' in the

icon stand for 'Acceleration', 'Velocity' and 'Displacement'.

Measurement

Measurement
quantity
(icon)

Measurement
tasks

Overall velocity >600RPM

Overall velocity >120RPM

Measurement
setup

Sensor setup

Evaluation
setup

RPM

Velocity / 10-1000 Hz

VIB 6.140

ISO 10816-3 group 2

Velocity / 2-1000 Hz

VIB 6.142

ISO 10816-3 group 1

RPM measurement

No measurement

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды