PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 36

Страница: 36 / 176

2-24

VIBXPER

T II 05.2012

Getting started - Basic settings

Left:

Registration menu

Right:

Units menu

The VIBXPERT PC license automates the

device registration process in OMNI-

TREND.

Registration

The functions and operating modes in VIBXPERT are distributed in

individual modules* that can be enabled by password as required.

VIBXPERT is supplied in the 'Basic' version with which overall values

as well as (limited) spectra can be measured. For example, to enable

the standard 1-channel version, the 'VIBXPERT firmware for 1 chan-

nel' module must be registered in VIBXPERT. The corresponding pass-

word can be found on the associated registration certificate:
• Click on 'Registration'.

• Click on the module to be registered and enter the password in the

text editor.

VIBXPERT PC license

Before VIBXPERT can exchange data with OMNITREND, the device

must be registered in OMNITREND. This is generally performed by

entering the PC license password in OMNITREND.
Here you can enter the password in VIBXPERT. The password is then

automatically read into OMNITREND when VIBXPERT first makes

contact with OMNITREND.

Units

The units - where appropriate - are set to SI units in the factory. To

change the unit for the respective measurement quantities, proceed

as follows:
• Click on 'Units'.

• Select the units for the measurement quantities.
The accuracy in decimal places appears in the lower area of the win-

dow for the current unit as well as the conversion factor for the asso-

ciated SI unit. It is not yet possible to define, delete or edit units. The

number of decimal places can not be changed.
To accept the settings, press MENU and click on 'OK'.

*The attachment on page 6-20 contains

an overview of the modules and the

available measurement functions.

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды