PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 162

Страница: 162 / 176

6-12

VIBXPER

T II 05.2012

Appendix - VIBCODE

Attention!

Measuring with VIBCODE

Never use the VIBCODE sensor to take a measurement directly from

the machine surface. This sensor must always be locked onto the

measuring pin!
Do not remove the VIBCODE sensor neither from the VIBCODE

measurement location nor from VIBXPERT during measurement.

Connecting the VIBCODE sensor*

Insert the sensor straight into the measurement location, press it in

place lightly and lock it by turning it clockwise until it stops.
This secure connection ensures that the measurement direction and

pressure are the same for each measurement and that the results are

reproducible.
To disconnect the sensor, turn it in the opposite direction and remove

it from the measurement location.
Connect the sensor cable to the measurement channel that is set in the

measurement task (A or B).

60°

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды