PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 158

Страница: 158 / 176

6-8

VIBXPER

T II 05.2012

Appendix - VIBXPERT utility

Transferring files

The following files can be transferred from the device to the PC:

- PDF files generated with a PDF printer driver.

- Screenshots generated by pressing <F> & <-> simultaneously .

- Results in CSV format for analysis and display in a spreadsheet

program (eg MS Excel).

• Click on the 'Get files' button.

• Then click on the respective button and select the files you wish to

transfer.

• Click on 'Transfer' to start the file transfer.

'Export *.xls' exports results into a MS Excel file.

Use 'Delete' to remove a file from the device.

'Close' closes the file selection window.

Get files

File selection window

System

Transferring system files

You can perform the following procedures:

- Backup and restore of the data and device configuration

- Format CF memory card.

- All the above mentioned steps in a procedure ('Defragmentation').
• Click on the 'System' button.

• To perform a data backup, click on 'Backup'.

• In the screen that opens, select the data category (Settings / Re-

sults) and enter the target directory, if necessary.

• Click on 'Backup' to start the procedure.

The 'Restore' procedure is performed in the same manner.

Backup settings

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды