PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 140

Страница: 140 / 176

5-20

VIBXPER

T II 05.2012

Measurement tasks

Multi-measurement task ('Multitask')

A multi-measurement task shortens the measurement times by com-

bining several, similar measurement tasks*. It is particularly time-

saving in the case of measurement tasks that are measured at the

same measurement location with the same transducer and the same

filter settings. In this case, VIBXPERT only carries out one signal mea-

surement and calculates the results of the individual measurement

tasks from this.
Initially, no measurement results appear in the Results screen, just

information on the status of the measurement together with the as-

sessment of the results (see below).

Evaluating the results

The evaluation of the results is carried out on the basis of the stored

thresholds. If a threshold is exceeded, the corresponding symbol ap-

pears in the 'Status' column (see below left).
• For a detailed view of the evaluation scale, press the MENU key

and click on 'Evaluation Overview' (see below).

Result of the single measurements

• After the measurement, press a navigation key until a black frame

appears around the list field.

• Press 'Enter' to activate the list field.
• Click on the measurement in the list whose result is to be dis-

played.

• Press ESC to return to the list field.

* e.g. shock pulse value + en
velocity spectrum

Alarm

Warning

Prewarning

Measuring

Measured

Error

Multitask

Result display (left)

Evaluation (right)

Status / evaluation icons

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды