PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 126

Страница: 126 / 176

5-6

VIBXPER

T II 05.2012

Measurement tasks

Runup / Coastdown

The runup and coastdown curves record the changes in the vibration

behavior of the machine when it starts up or shuts down. This analy-

sis function can be used to determine the resonance frequencies of a

machine. The following types of measurement are available for this

purpose:
- Phase vector (amplitude and angle), dependent on the RPM

- Spectrum, dependent on the RPM

- Overall value, dependent on the RPM

Runup

Measurement is started

before

the machine is switched on. VIB XPERT

records the current RPM and automatically begins with measure-

ment as soon as the selected start RPM is exceeded. Measurement is

stopped when the stop RPM is reached.

Coastdown

Measurement is started

while

the machine is running at the operating

RPM. VIBXPERT then begins to measure the RPM continuously. Once

you have switched the machine off and it drops below the selected

start RPM, VIBXPERT automatically starts recording the data. Mea-

surement stops once the selected stop RPM is reached. Start and stop

RPMs are defined in the measurement setup (see p. 3-22).

A. Selecting the measurement task

The measurement tasks for a runup / coastdown curve are located in

the 'Advanced' tab. The measurement types 'Phase - RPM' and 'Spectra

- RPM' are assigned a task icon; the 'Overall Value - RPM' measure-

ment type has its own icon.

Left:

Selecting the

measurement task

Right:

Starting the measurement

Overall value - RPM

Runup / Coastdown

Overall values (RPM)

Runup / Coastdown

Phase, spectra (RPM)

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды