PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 116

Страница: 116 / 176

4-22

VIBXPER

T II 05.2012

Reports

Left:

Report configuration

General information

Right:

Report configuration

Information on the spectrum specific to

the measurement type

A measurement report is used to create detailed documentation on a

measurement. The report contains the results, general information on

the operator and additional measurement information. Measurement

reports are available for the following measurements:

pectrum

, t

ime

waveform

, o

verall

values

trend

, t

rending

pectrum

, B

ancing

Configuring the measurement report

Which information is contained in the measurement report is defined

in the report configuration. Every measurement has a standard report

configuration that is adequate for most cases. The standard configura-

tion can be neither edited nor deleted. To create a new report configu-

ration, proceed as follows:
• Press the MENU key in the result screen.

• Select 'Print' and click on 'Report printouts'.

The report configuration appears (see below).

• Select the ‘Reports’ field.

• Press the MENU key and click on 'New'.

• Enter a name in the text editor.

• In the 'Common settings' tab, select the entries that are to appear

in the measurement report:

ompany

: Company name that appears on the report. To change it,

click on the text field. The changed company name is used in all

report configurations.

ogo

: Company logo that is printed in the report. Transfer the new

logo using the 'VIBXPERT utility' program (see p. 6-7). File format:

PNG, image size: max. 186 pixels (longest side).

ustomer

: The customer information is stored globally and can be ac-

cessed by any report configuration. Select the customer from the

menu, or create a new customer as follows:

• Open the customer selection menu and click on the lowest entry,

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды