PRÜFTECHNIK VIBXPERT II Скачать руководство пользователя страница 111

Страница: 111 / 176

4-17

VIBXPER

T II 05.2012

Configuring the result display (Display Setup)

In the Results display, after a measurement:

• Press the MENU key and click on 'Display Setup'.
In the selection field of the measurement tasks (Multimode):

• Highlight the measurement task symbol.

• Press the MENU key and highlight the 'Display Setup' entry.

• Press the navigation key right and click on 'Measurement' or 'Trend'

respectively (s. below).

X. Continuous measurement (‘live mode’)

In ‘Live mode’, you can check the signal quality before beginning with

data collection (see p. 3-4).

A1. Display Setup for measurement: Overall values

isplay

limit

...:

The limit values can be displayed as an absolute

value or as a difference ('Delta value') to the measurement value.

isplay

overall

peak

value

Select the characteristic vibration value that

is to be displayed by default with the 'RMS value'. After the mea-

surement, press the navigation key up repeatedly to display the

overall values of the series that were not displayed. If the thresh-

old value is exceeded, the RMS values and the overall value that

exceeded the threshold value by the largest amount are displayed.

A2. Display-Setup for Trend: Overall values

eas

value

Selection of

overall values

. The

line type

can be selected

and the

labeling

can be shown for each trend curve.

how

...:

Limits, event markers, references

and the associated

labeling

can be displayed in the chart. The

line type

can be selected.

oom

: Speed or step size when zooming

ayout

: The values on the trend curve can be identified with

markers

grid

can be displayed for easier evaluation of the data and the

cursor can be displayed as a cross (

short

) or line cursor (

long

Left:

Opening the Display Setup

before a multimode measurement

Right:

Display Setup for Overall Trend

Display setup

Display Setup

for overall values with more than two
quantities.

Содержание VIBXPERT II

















































































































































































Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды

PRÜFTECHNIK VIBXPERT II, Руководство по эксплуатации

Результаты поиска

Содержание VIBXPERT II

Отзывы:

Бренды по названию

Популярные бренды