Proximus Forum 500 Series Скачать руководство пользователя страница 90

Страница: 90 / 348

Preliminary Information

Scope of Delivery

A Forum Gateway 560’s scope of delivery comprises:

●

1 19" frame (1-12 frame) with slots for 1 control module and up to
2 power supply units and 12 interface cards

The basic configuration of a 19" frame includes the following components:

– 1 BPV+1-12 backplane

– 1 Forum 550 Power Supply unit

– 1 mains cable for connection to the mains supply

– 1 control module Forum 550 Card main processor

– 1 Compact Flash Card;
the configuration and firmware of the gateway are stored on this card

●

1 set of mounting brackets and screws for installing the frame in a 19" rack

●

1 set of dummy covers for covering unused slots

Содержание Forum 500 Series





























































































































































































































































































































































Результаты поиска

Содержание Forum 500 Series

Отзывы:

Proximus Forum 500 Series, Руководство по монтажу и пусконаладке, Страница: 90 / 348

Результаты поиска

Содержание Forum 500 Series

Отзывы: