Proximus Forum 500 Series Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 348

background image

DECT Synchronisation

66

Forum 5004/5008/5012 and Gateways

An audio channel is seized when an audio connection is to be established
between VoIP and TDM. Alongside call connections from VoIP telephones to
TDM terminals, this comprises:

●

Call connections between 2 TDM terminals connected to different
hardware units.

●

Music on Hold: generated as VoIP data stream by the Forum 5004/5008/
5012 communications system.

●

Forum Voicemail and Forum Auto Attendant: Recording and playing as
VoIP data stream via the Forum 5004/5008/5012 communications
system.

●

Audio tones such as ringing tone, busy signal, dialling tone, etc. are
generated as VoIP data stream by the Forum 5004/5008/5012 commu-
nications system.

Note:

TDM terminals on the same gateway do not seize an audio
channel during call mode, however, the terminals do briefly
seize an audio channel for the dial tone while establishing the
call connection.

DECT Synchronisation

The IP-based connection between the hardware units of the Forum 5004/
5008/5012 communications system and does not allow transmission of a
TDM synchronisation signal. The TDM synchronisation signal is, however,
generally necessary for operating DECT base stations (TDM RFPs). This
means that all DECT base stations connected via U

pn

have to be connected to

the same hardware unit in order to support a transparent handover between
the DECT base stations.

Gateway Configuration

The call server must be configured for this operation if you operate a call
server along with one or multiple gateways. The various configuration
variants are described in the following sections.

«
...
66
67
68
69
70
...
»

Содержание Forum 500 Series





























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Forum 500 Series

Бренд: Panasonic Страницы: 5

Бренд: Panasonic Страницы: 14

Бренд: Panasonic Страницы: 2

VoiceSonic KX-NT700

Бренд: Panasonic Страницы: 8

Бренд: Blaupunkt Страницы: 15

TesiraFORTÉ AVB VT4

Бренд: Biamp Страницы: 2

realpresence trio 8800

Бренд: Polycom Страницы: 7

Бренд: Jensen Страницы: 48

Бренд: Digitrax Страницы: 8

Бренд: Konftel Страницы: 8

Бренд: Champion Страницы: 46

Бренд: Panasonic Страницы: 24

Бренд: Duro Dyne Страницы: 16

DOCKCONTROLLER DC-200

Бренд: Motorola Страницы: 16

Бренд: HP Страницы: 174

Бренд: Bosch Страницы: 252

Бренд: Kenwood Страницы: 40

Бренд: Kenwood Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды