Proximus Forum 500 Series Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 348

background image

Forum Gateway 560 Modules

129

Configurator

in the web console (see

Installing Interface Cards

Forum 550 Card 8 analogue extensions

Field of application

The Forum 550 Card 8 analogue extensions interface card provides eight
analogue interfaces for connecting analogue terminals.

The Forum 550 Card 8 analogue extensions interface card can be installed in
any of the slots (1 to 12) of a Forum Gateway 560 (see

Technical information

●

The Forum 550 Card 8 analogue extensions interface card can – when
operating multiple Forum Gateways 560 – be operated on any
Forum Gateway 560.

●

The Forum 550 Card 8 analogue extensions interface card supports pulse
dialling as well as dual-tone multi-frequency (DTMF) dialling.

●

Calling line identification presentation (CLIP) is supported.

●

Busy tone detection is not supported.

●

The Forum 550 Card 8 analogue extensions interface card runs on
software acquired from the system. After the card has been installed it will
automatically load the required software.

●

No settings need to be made on the Forum 550 Card 8 analogue exten-
sions interface card.

Pin assignment

For information on the a/b interface pin assignment, refer to

starting on page 111.

Indicators

There are four LEDs on the front of the Forum 550 Card 8 analogue
extensions interface card.

«
...
129
130
131
132
133
...
»

Содержание Forum 500 Series





























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Forum 500 Series

ProducTVity Station

Бренд: red lion Страницы: 8

SCALA UTOPIA III EVO

Бренд: Focal Страницы: 52

Бренд: Avaya Страницы: 5

Бренд: Delta Страницы: 19

Бренд: Quanser Страницы: 4

Бренд: Nexus Страницы: 97

Бренд: iPECS Страницы: 101

Бренд: Panasonic Страницы: 24

Бренд: LG Страницы: 20

Бренд: LG Страницы: 24

Бренд: LG Страницы: 47

Бренд: LG Страницы: 8

Бренд: LG Страницы: 18

Бренд: LG Страницы: 22

Бренд: LG Страницы: 18

Бренд: LG Страницы: 10

Бренд: LG Страницы: 16

Бренд: LG Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды