Protrol IPC4020 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 63

background image

IPC402x-UM-2209-1-2.x.x (en)

Ensto Protrol AB

Phone: +46 31 45 82 00

Alfagatan 3

internet: www.protrol.se

431 49 Mölndal, SWEDEN

8

e-mail: [email protected]

The table beneath describes the other LED indicators on the front panel.

LED

Description

PWR

Green diode indicating that the device is powered up

RUN

Green diode normally flashing at 0.5 Hz frequency

EVNT

Yellow diode indicating that there is an unsent telegram in the queue for slave transmission
on the system interface

AUX

Yellow diode that normally indicates that the device is handling a frequency deviation

IRF

Red diode that indicates internal fault

USB

Yellow diode indicating a connected USB port

OC

Red diode indicating that an overcurrent has been detected

EF

Red diode indicating that an earth fault has been detected

Tx Master

Yellow diode indicating that a telegram is being sent on the serial master interface

Rx Master

Yellow diode indicating that a telegram is being received on the serial master interface

Tx Slave

Yellow diode indicating that a telegram is being sent on the serial slave interface

Rx Slave

Yellow diode indicating that a telegram is being received on the serial slave interface

Tx/Rx (USB)

Dual-coloured green-red diode which alternates when there is traffic on the USB port.

EX1

Yellow diode indicating that Detector 1 has identified a fault

EX2

Yellow diode indicating that Detector 2 has identified a fault

– applies to expanded device

EX3

Yellow diode indicating that Detector 3 has identified a fault

– applies to expanded device

EX4

Yellow diode that in normal configuration indicates start fault detection, detector 1-3

Some LEDs, such as AUX and EX1-4, can have other functionality for certain option choices.

4.1.1 Push-button for Local Acknowledge

There is a push-button, ACN, on the far right of the front panel for local acknowledge of the overcurrent
and earth fault indications, and factory reset. Remote acknowledge from the dispatch center and automatic
self-acknowledge after a configurable time delay are described in a separate chapter of this text manual.

4.2 Startup

After a restart of the device, i.e., if there has been a disturbance in DC supply or a restart has been ordered
from remote, inputs and outputs are updated with the current status. Any outputs that were activated
before the restart, return to inactive position unless the conditions for activation are valid.

«
...
6
7
8
9
10
...
»

Содержание IPC4020
































































Отзывы:

Нет отзывов

Похожие инструкции для IPC4020

Vb-C60 - Ptz Network Camera

Бренд: Canon Страницы: 76

Concord express

Бренд: GE Страницы: 3

Concord express

Бренд: GE Страницы: 32

Бренд: Uniden Страницы: 12

Бренд: Observint Страницы: 24

Бренд: LEGRAND Страницы: 6

Бренд: NEO Coolcam Страницы: 8

Бренд: ADT Страницы: 62

Бренд: M2M Страницы: 7

Terminator ZE-B

Бренд: Thermon Страницы: 4

Бренд: i3 International Страницы: 2

Бренд: echoflex Страницы: 20

NAC-HD-326VL/60-G

Бренд: Navaio Страницы: 2

Бренд: ADEMCO Страницы: 3

Бренд: Eagle Eye Networks Страницы: 5

Бренд: ACTi Страницы: 37

Бренд: urmet domus Страницы: 40

Бренд: Night Owl Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды