Protrol IPC4020 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 63

background image

IPC402x-UM-2209-1-2.x.x (en)

Ensto Protrol AB

Phone: +46 31 45 82 00

Alfagatan 3

internet: www.protrol.se

431 49 Mölndal, SWEDEN

50

e-mail: [email protected]

Settings

–

Phase Break

:

Parameter

Description

Range

Factory value

Unit

Enable

Phase break function activated

Yes or No

No

-

Low Level

Max nivå för förlorad fas och summaström

Max current for lost phase and residual current

0.1..1000.0

5.0

A

High Level

Min current level for healthy phases

0.1..1000.0

20.0

A

Delay

Time delay between

START

and

TRIP

0..10 000

5 000

ms

Trip relay

TRIP

output relay

0..8

0 (non)

-

Relay pulse

Pulse length of

TRIP

output signal

100..10 000

500

ms

8.6.1 Auto reclosing

– OPTION

Auto reclosing (AR -

RECL

) means that a delayed switch-on is ordered after an initial

TRIP

has been issued

by any of the Overcurrent or Earth fault Protrol protection functions. This option can be acquired for one
bay only, or for all three bays.

Activation of the function can be made at the device using a binary input, or the ACN button. It can also be
ordered by the remote control centre. The ACN button must be pressed 5 s before toggling takes place.
Indication to and order from SCADA is configured as double point / double command, see

I/O-addressing/Binary inputs/Detector m/RECL OFF/ON

and

I/O-addressing/Binary outputs/Detector m/

RECL OFF/ON,

respectively. These objects are blocked from factory.

Visual indication of AR OFF/ON can be chosen as follows:

AR for Detector 1

–

outputs 1

–

8, however, always AUX-LED

AR for Detector 2 and 3

–

outputs 1

–

8, and/or AUX-LED

After reclosure the function is always OFF. Reactivation can be done from SCADA but will always be done
automatically by Acknowledge after a preset time or by pressing the ACN button. Also, a restart of the
device inactivates AR. Manual switch-on of the circuit breaker blocks auto reclosure for 60 s.

The event log shows events for AR OFF/ON, AR startad and AR executed:

RECL OFF

,

RECL ON

,

RECL Started

,

RECL Executed

.

Settings

–

Auto reclosing

:

Parameter

Description

Range

Factory value

Unit

Enable

Choice of function that starts auto reclosing

Disabled/

OC/EF/OC&EF

Disabled

-

Delay

Time delay for auto reclosing

500..60 000

30 000

ms

Reclosure relay

Output relay for reclosing (

ON

output)

0..8

0 (None)

-

Relay pulse

Pulse length of

ON

output signal

100..10 000

500

ms

Input ON/OFF

Input for local activation of auto reclosing

ACN, 1..16

ACN

-

Output indication

Output or LED for local indication OFF/ON

1..8, AUX LED

AUX LED

-

It is strongly recommended to use the Non-directional earth fault function with activation after switch-on
to ensure safe detection of a permanent earth fault after the auto reclosure operation.

«
...
48
49
50
51
52
...
»

Содержание IPC4020
































































Отзывы:

Нет отзывов

Похожие инструкции для IPC4020

Бренд: Varian Страницы: 176

Бренд: L-Sniper Страницы: 12

Бренд: jablotron Страницы: 16

Бренд: X10 Страницы: 4

LevelPro ProScan 3 Series

Бренд: ICON Страницы: 14

Level pro 200C Series

Бренд: ICON Страницы: 19

Interlogix TX-E231

Бренд: United Technologies Страницы: 2

Бренд: ADT Страницы: 29

ZS 80 KST Extreme Series

Бренд: steute Страницы: 20

Бренд: Q-See Страницы: 9

Бренд: jablotron Страницы: 2

Бренд: HomeSeer Страницы: 2

Бренд: XNET Страницы: 17

Бренд: Safety Technology International Страницы: 4

Бренд: RAB Lighting Страницы: 7

Бренд: Samcon Страницы: 44

Бренд: Sensor Espio Страницы: 37

Бренд: Vivotek Страницы: 387

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды