Protocol Propaq 242 Скачать руководство пользователя страница 69

Страница: 69 / 120

Propaq CS Directions for Use

Printing &

rends

Print Multiple Trends Manually or Automatically

Press

SETUP, MORE, PRINTER

from the Main Menu

to display the Printer Setup Page:

Press

NEXT

as needed to scroll down to the parameters listed below AUTO TREND (NIBP,

RESP, etc.).

Press

NEXT

and

CHANGE

to set desired trends to ON.

To manually print all selected trends, press

PRINT TREND

on this page or press

PRINT TRENDS

the bottom front panel of the monitor.

You can print all selected trends at any time by pressing this

PRINT TRENDS

button.

To program the monitor to automatically print selected trends every four hours, press

NEXT

needed to highlight AUTO TREND, then press

CHANGE

to select the hours for printing.

For example, if you select 01 05 09 13 17 21 at 4:27, the printer will automatically print selected trends
first at 5:00, then 9:00, etc.

Delete All Patient Trends

To delete all trends recorded for a patient, turn off the monitor.

PRINTER

TEMP

100.4

98.6

1.8

( 15)

mmHg

(M)

S
D

NIBP

( 85)

mmHg

(M)

122
58

MCO

mmHg

Br/m

S
D

∆

SETUP PAGE

AUTO TREND : 01 05 09 13 17 21

CONTINUOUS
AUTO PRINT
ALARM PRINT
NIBP TICKET

APNEA TICKET

OXYCRG ON ALARM

NIBP :

RESP : OFF

: ON

: 25.0 mm/s
: OFF
: OFF
: OFF
: ON
: OFF

: OFF

CHANGE

TREND

TEMP : OFF

Press to print all
selected trends.

Press to scroll to
the next selection.

Press to change
the displayed
value.

Specifies what time the trends

automatically print. Trends are printed

every 4 hours beginning at either

01, 02, 03, or 04 hours.

(OFF=no printing.)

Select ON to include in trend printing.

Содержание Propaq 242

























































































































Результаты поиска

Содержание Propaq 242

Отзывы:

Похожие инструкции для Propaq 242

Бренды по названию

Популярные бренды

Protocol Propaq 242, Инструкция по применению

Результаты поиска

Содержание Propaq 242

Отзывы:

Похожие инструкции для Propaq 242

Бренды по названию

Популярные бренды