Protocol Propaq 242 Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 120

Protocol Propaq 242 Скачать руководство пользователя страница 109

Propaq CS Directions for Use

109

Ref

erence

Alarms Specifications

Characteristic

Specification

Indicators (see table below)

Red indicator light: flashing light indicates patient alarm; continuously on
indicates patient alarms are suspended.
Yellow indicator light: continuously on indicates one or more alarm limits have
been disabled; flashing light indicates an equipment alert.

Tone Frequency

900 Hertz
Tone is steady for a patient alarm and sounds for 1 second every 4 seconds for
an equipment alert.

Selectable Tone Volume

Low, Medium, High

Limits

Settable on all parameters

Control

Automatic preset or manual settings

Alarm Priority

Highest priority: Apnea, then patient alarms
Lowest priority: Equipment alerts

Alarm on Tachycardias

Most tachycardias will alarm in less than 8 seconds. These include AAMI 3.1.2.1
part f. waveforms. Certain multifocal tachycardias may initially alarm as “low rate.”

Apnea delay setting

Adult/Ped = 6, 10, 15, 20, 25, 30 seconds
Neonate = 6, 10, 15, 20 seconds

Alarm Holdoff Time Period

1

1. To help minimize false alarms, the monitor briefly delays or “holds off” triggering alarms for limit violations for these vital
signs. After the alarm holdoff period begins, if the monitor detects that the patient’s vital sign has returned to acceptable
limits, the monitor cancels the alarm holdoff. The next time a vital sign limit is violated, the monitor starts a new holdoff
period.

HR/PR = 3 seconds (except NIBP PR)
SpO

2

= 10 seconds

RR/BR = 5 seconds

Audio Alarm Holdoff with
Acuity

When a Propaq CS monitor in Adult or Pediatric Mode is connected to an Acuity
System, the audio alarms at the bedside monitor can be delayed up to 4 minutes
and 15 seconds. The delay time is selected in Acuity software at the time of
Acuity installation. Visual alarm indications and Nurse Call alarm are not delayed.

Propaq CS Monitor Alarm Indications

Patient and Alarm Limit Status

Red

Alarm

Yellow

Alarm(s)

Off

Nurse

Call

Tone

Patient in alarm condition, and all alarm limits on

FLASH

OFF

ON

ON

Patient in alarm condition, and at least one alarm limit is off

FLASH

ON

ON

ON

Patient alarms suspended (whether in alarm condition or not)
and at least one alarm limit is off

ON

ON

OFF

OFF

Patient alarms suspended (whether in alarm condition or not)
and all alarm limits are on

ON

OFF

OFF

OFF

Patient not in alarm condition, and at least one alarm limit is off.

OFF

ON

OFF

OFF

Equipment alert, patient not in alarm condition

OFF

FLASH

OFF

ON 1 s,
OFF 4 s

Equipment alert, patient alarms suspended

ON

FLASH

OFF

OFF

«
...
107
108
109
110
111
...
»

Содержание Propaq 242

























































































































Отзывы:

Нет отзывов