DEL2104 Issue 4 02/11 SB
Page 1 of 3
Copyright © Protec Fire Detection plc 2010
6000
PLUS
/OPHTCO/S Installation, Commissioning and Service Instructions
Overview
The Protec 6000
PLUS
/OPHTCO/S is a loop powered Fire sensor which reports Smoke, Thermal and Carbon Monoxide levels
in its installed location to the fire alarm control panel. The sensor is also equipped with an integrated loop powered sounder.
Technical Specification
Loop protocol
Protec Algo-tec™ 6000
PLUS
Loop isolator fitted
Yes
Loop voltage range
18 to 27V Algo-tec™ loop
Loop average quiescent current (24V loop)
0
.
45 mA
Loop average alarm current (24V loop )
5mA
Analogue values
Smoke
Thermal
Carbon Monoxide
Normal 40 to 60 bits
Fault Low <35 bits
Fault low High>90 bits
Normal 80 to 180 bits
Fault Low <25 bits
Fault High>250 bits
Normal 30 to 100 bits
Fault Low <20 bits
Fault High>150 bits
Indications
On-board red indicating LED
Environmental operational limits
-10 to 50 degrees C ( 95% RH no condensation or icing )
Sounder Frequencies
Continuous 990Hz, Warble 730Hz to 990Hz, Pip 990Hz
Sounder synchronisation
Sounder synchronisation is achieved by panel control
IP rating
IP21C
Isolator Specification
Please see Protec DEL2110 for details
Installation
1. Base options: 6000PLUS/BASE
LPCB Approved as part of product approval
6000PLUS/FFBASE
LPCB Approved as part of product approval
28-075-01 (Plug and Play Fast Fix)
LPCB Approved as part of product approval
28-075-02 (Plug and Play Surface)
LPCB Approved as part of product approval
Note: See individual information sheets for base wiring details.
2. Install the detector in the base, turn firmly clockwise.
Commissioning
1. Each 6000
PLUS
/ detector has a unique serial number which will be used as part of the commissioning of the fire alarm
system. It is necessary to remove one of the ‘peelable’ bar code labels present on the product and place it in the
commissioning booklet supplied with each Protec addressable control panel. The bar code sticker should be placed at the
relevant loop and address position intended. It is important that serial numbers are not mixed otherwise the addressing of
the 6000PLUS/OPHTCO/S will be incorrect when commissioned.
2.
Commission the device onto the system as detailed in the installation and commissioning manual for the fire alarm panel
being used.
6000
PLUS
/OPHTCO/S Certification Details
EN Standards Compliance/ Approvals table
0 8 3 2
Protec Fire Detection plc, Nelson, Lancashire, England, BB9 6RT
10
0832-CPD-1177
EN 54 - 5
Point type heat detector
Class A2
6000
PLUS
/OPHTCO/S
EN 54 - 7
Point type smoke detector
6000
PLUS
/OPHTCO/S
EN 54 - 3: 2001 + A1 + A2
Alarm devices – Sounder
Type A: For indoor use
6000
PLUS
/OPHTCO/S
EN 54 - 17:2005
Short-circuit isolator
6000
PLUS
/OPHTCO/S
Technical Data included in this datasheet DEL2104 Issue 4
High Sensitivity
Med Sensitivity
Low Sensitivity
Isolator/sounder
No Approval
Approved to:
EN 54-7: 2000 + A1: 2002 + A2: 2006
EN 54-5: 2000 + A1: 2002, Class A2
CEA 4021:2003-07
Approved to:
EN 54-7: 2000 + A1: 2002 + A2: 2006
EN 54-5: 2000 + A1: 2002, Class A2
CEA 4021:2003-07
Approved to:
EN 54-17: 2005
EN 54-3: 2001 + A1: 2002 + A2:
2006