ProSoft Technology ProLinx DNPS Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 86

background image

Important Installation Instructions

Power, Input, and Output (I/O) wiring must be in accordance with Class I, Division 2 wiring methods, Article 501-4 (b)
of the National Electrical Code, NFPA 70 for installation in the U.S., or as specified in Section 18-1J2 of the Canadian
Electrical Code for installations in Canada, and in accordance with the authority having jurisdiction. The following
warnings must be heeded:

A

WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR
CLASS I, DIV. 2;

B

WARNING - EXPLOSION HAZARD - WHEN IN HAZARDOUS LOCATIONS, TURN OFF POWER BEFORE
REPLACING OR WIRING MODULES

C

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN
SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS.

D

THIS DEVICE SHALL BE POWERED BY CLASS 2 OUTPUTS ONLY.

All ProLinx

®

Products

WARNING – EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN
SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.

AVERTISSEMENT – RISQUE D'EXPLOSION – AVANT DE DÉCONNECTER L'EQUIPMENT, COUPER LE
COURANT OU S'ASSURER QUE L'EMPLACEMENT EST DÉSIGNÉ NON DANGEREUX.

Markings

UL/cUL

ISA 12.12.01 Class I, Div 2 Groups A, B, C, D

cUL

C22.2 No. 213-M1987

243333

183151

CL I Div 2 GPs A, B, C, D

Temp Code T5

II 3 G

Ex nA nL IIC T5 X

0° C <= Ta <= 60° C

II – Equipment intended for above ground use (not for use in mines).

3 – Category 3 equipment, investigated for normal operation only.

G – Equipment protected against explosive gasses.

ProLinx Gateways with Ethernet Ports

Series C ProLinx™ Gateways with Ethernet ports do

NOT

include the HTML Web Server. The HTML Web Server

must be ordered as an option. This option requires a factory-installed hardware addition. The HTML Web Server now
supports:

8 MB file storage for HTML files and associated graphics files (previously limited to 384K)

32K maximum HTML page size (previously limited to 16K)

To upgrade a previously purchased Series C model:

Contact your ProSoft Technology distributor to order the upgrade and obtain a Returned Merchandise Authorization
(RMA) to return the unit to ProSoft Technology.

«
1
2
3
4
...
»

Содержание ProLinx DNPS























































































Отзывы:

Нет отзывов

Похожие инструкции для ProLinx DNPS

Бренд: UrsaLeo Страницы: 5

Бренд: AudioCodes Страницы: 5

Бренд: Grandstream Networks Страницы: 10

Бренд: NetComm Страницы: 2

Бренд: Comtrend Corporation Страницы: 84

Бренд: iSMA CONTROLLI Страницы: 29

Бренд: SolarEdge Страницы: 49

Бренд: Odin TeleSystems Страницы: 36

Бренд: 4IPNET Страницы: 12

Бренд: ZyXEL Communications Страницы: 5

Бренд: Exegin Страницы: 84

Бренд: Abit Страницы: 7

Бренд: SmartRG Страницы: 16

Бренд: Bogen Страницы: 33

50.0070.0001.00

Бренд: FP Страницы: 98

Бренд: Advantech Страницы: 42

Бренд: Telstra Страницы: 7

Бренд: Arris Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды