manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Поделиться
Скачать
ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 83

Support, Service & Warranty 

MVI56-CAS 

♦

 ControlLogix Platform 

 

Teledyne CA Slave Module 

 

ProSoft Technology, Inc. 

Page 83 of 86 

December 26, 2007 
 

6.5.10 Allocation of risks 

This Warranty allocates the risk of product failure between ProSoft and the 
Customer. This allocation is recognized by both parties and is reflected in the 
price of the goods. The Customer acknowledges that it has read this Warranty, 
understands it, and is bound by its Terms. 

6.5.11 Controlling Law and Severability 

This Warranty shall be governed by and construed in accordance with the laws of 
the United States and the domestic laws of the State of California, without 
reference to its conflicts of law provisions. If for any reason a court of competent 
jurisdiction finds any provisions of this Warranty, or a portion thereof, to be 
unenforceable, that provision shall be enforced to the maximum extent 
permissible and the remainder of this Warranty shall remain in full force and 
effect. Any cause of action with respect to the Product or Services must be 
instituted in a court of competent jurisdiction in the State of California. 

Содержание inRAx MVI56-CAS























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды