manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Поделиться
Скачать
ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 59

Reference MVI56-CAS 

♦

 ControlLogix Platform 

 

Teledyne CA Slave Module 

 

ProSoft Technology, Inc. 

Page 59 of 86 

December 26, 2007 
 

If you see the status as running, you will not be able to use this com port for 
anything other than communication to the processor. To stop the driver press 
the "Stop" on the side of the window: 

 

5 

After you have stopped the driver you will see the following: 

 

6 

Upon seeing this, you may now use that com port to connect to the debug 
port of the module. 

Note:

 You may need to shut down and restart your PC before it will allow you to stop 

the driver (usually only on Windows NT machines). If you have followed all of the 
above steps, and it will not stop the driver, then make sure you do not have RSLogix 
open. If RSLogix is not open, and you still cannot stop the driver, then reboot your PC. 

5.3.2 RS-232 

When the RS-232 interface is selected, the use of hardware handshaking 
(control and monitoring of modem signal lines) is user definable. If no hardware 
handshaking will be used, the cable to connect to the port is as shown below: 

 

 

Содержание inRAx MVI56-CAS























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды