manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Поделиться
Скачать
ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 57

Reference MVI56-CAS 

♦

 ControlLogix Platform 

 

Teledyne CA Slave Module 

 

ProSoft Technology, Inc. 

Page 57 of 86 

December 26, 2007 
 

5.3 Cable 

Connections 

The application ports on the MVI56-CAS module support RS-232, RS-422, and 
RS-485 interfaces. Please inspect the module to ensure that the jumpers are set 
correctly to correspond with the type of interface you are using.  

Note:

 When using RS-232 with radio modem applications, some radios or modems 

require hardware handshaking (control and monitoring of modem signal lines). Enable 
this in the configuration of the module by setting the UseCTS parameter to 1. 

5.3.1 RS-232 

Configuration/Debug Port 

This port is physically an RJ45 connection. An RJ45 to DB-9 adapter cable is 
included with the module. This port permits a PC based terminal emulation 
program to view configuration and status data in the module and to control the 
module. The cable for communications on this port is shown in the following 
diagram: 

 

 

Disabling the RSLinx Driver for the Com Port on the PC 

The communication port driver in RSLinx can occasionally prevent other 
applications from using the PC's COM port. If you are not able to connect to the 
module's configuration/debug port using ProSoft Configuration Builder (PCB), 
HyperTerminal or another terminal emulator, follow these steps to disable the 
RSLinx Driver. 

1 

Open RSLinx and go to Communications>RSWho 

Содержание inRAx MVI56-CAS























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды