ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 48

Страница: 48 / 86

MVI56-CAS

♦

ControlLogix Platform

Reference

Teledyne CA Slave Module

Page 48 of 86

ProSoft Technology, Inc.

December 26, 2007

5.1.3 Hardware

Specifications

Specification

Description

Backplane Current Load

800 mA @ 5 V DC; 3mA @ 24V DC

Operating Temperature

0 to 60°C (32 to 140°F)

Storage Temperature

-40 to 85°C (-40 to 185°F)

Shock 30g

Operational

50g non-operational
Vibration: 5 g from 10 to 150 Hz

Relative Humidity

5% to 95% (non-condensing)

LED Indicators

Module Status
Backplane Transfer Status
Application Status
Serial Activity

Debug/Configuration port (CFG)

CFG Port (CFG)

RJ45 (DB-9M with supplied cable)
RS-232 only

Application ports (PRT1 & PRT2)

Full hardware handshaking control, providing radio, modem and multi-drop support
Software configurable
communication parameters

Baud rate: 110 to 115,200 baud, depending on protocol
RS-232 and 422
Parity: none, odd or even
Data bits: 5, 6, 7, or 8
Stop bits: 1 or 2
RTS on/off delay: 0 to 65535 milliseconds

App Ports (P1,P2) (Serial modules)

RJ45 (DB-9M with supplied cable)
RS-232 handshaking configurable
500V Optical isolation from backplane

Shipped with Unit

RJ45 to DB-9M cables for each port
6-foot RS-232 configuration cable

5.1.4 Functional

Specifications

Function

codes

1: Read output data

2: Read analog data

3: Read meter data

10: Read frozen analog values

11: Read frozen meter data

16: Read all data

20: Read tank data from RTU

30: Control momentary select

31: Control momentary operate

32: Control continuous select

33: Control continuous operate

Содержание inRAx MVI56-CAS























































































Результаты поиска

Содержание inRAx MVI56-CAS

Отзывы:

Бренды по названию

Популярные бренды

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Результаты поиска

Содержание inRAx MVI56-CAS

Отзывы:

Бренды по названию

Популярные бренды