manualshive.com logo in svg

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Поделиться
Скачать
ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 39

Diagnostics and Troubleshooting 

MVI56-CAS 

♦

 ControlLogix Platform 

 

Teledyne CA Slave Module 

 

ProSoft Technology, Inc. 

Page 39 of 86 

December 26, 2007 
 

Important: 

When in analyzer mode, program execution will slow down. Only use this 

tool during a troubleshooting session. Before disconnecting from the Config/Debug 
port, please press 

[S]

 to stop the data analyzer, and then press 

[M]

 to return to the 

main menu. This action will allow the module to resume its normal high speed 
operating mode.  

Returning to the Main Menu 

Press 

[M]

 to return to the Main Menu. 

4.1.7  Data Analyzer Tips 

From the main menu, press 

[A]

 for the "Data Analyzer". You should see the 

following text appear on the screen: 

 

After the "Data Analyzer" mode has been selected, press 

[?]

 to view the Data 

Analyzer menu. You will see the following menu: 

 

From this menu, you can select the "Port", the "format", and the "ticks" that you 
can display the data in. 

For most applications, HEX is the best format to view the data, and this does 
include ASCII based messages (because some characters will not display on 
HyperTerminal and by capturing the data in HEX, we can figure out what the 
corresponding ASCII characters are supposed to be). 

The Tick value is a timing mark. The module will print a _TT for every xx 
milliseconds of no data on the line. Usually 10milliseconds is the best value to 
start with. 

Содержание inRAx MVI56-CAS























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды