ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 3

Страница: 3 / 86

Electrical Ratings

Backplane Current Load: 800 mA @ 5 V DC; 3mA @ 24V DC

Operating Temperature: 0 to 60°C (32 to 140°F)

Storage Temperature: -40 to 85°C (-40 to 185°F)

Shock: 30g Operational; 50g non-operational; Vibration: 5 g from 10 to 150

Relative Humidity 5% to 95% (non-condensing)

All phase conductor sizes must be at least 1.3 mm(squared) and all earth

ground conductors must be at least 4mm(squared).

Markings:

II 3 G 0C <=Ta<= 60C EEx nA IIC T4 DEMKO 07ATEX0710717X

Your Feedback Please

We always want you to feel that you made the right decision to use our products. If you have
suggestions, comments, compliments or complaints about the product, documentation or support,
please write or call us.

ProSoft Technology

1675 Chester Avenue, Fourth Floor
Bakersfield, CA 93301
+1 (661) 716-5100
+1 (661) 716-5101 (Fax)

http://www.prosoft-technology.com

MVI56-CAS User Manual
December 26, 2007
PSFT.CAS.MVI56.UM.07.12.26

ProSoft Technology ®, ProLinx ®, inRAx ®, ProTalk® and RadioLinx ® are Registered Trademarks
of ProSoft Technology, Inc.

Содержание inRAx MVI56-CAS























































































Результаты поиска

Содержание inRAx MVI56-CAS

Отзывы:

Бренды по названию

Популярные бренды

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Результаты поиска

Содержание inRAx MVI56-CAS

Отзывы:

Бренды по названию

Популярные бренды