ProSoft Technology inRAx MVI56-CAS Скачать руководство пользователя страница 10

Страница: 10 / 86

MVI56-CAS

♦

ControlLogix Platform

Start Here

Teledyne CA Slave Module

Page 10 of 86

ProSoft Technology, Inc.

December 26, 2007

100 Mbytes of free hard disk space (or more based on application

requirements)

256-color VGA graphics adapter, 800 x 600 minimum resolution (True Color

1024

768 recommended)

CD-ROM

drive

HyperTerminal or other terminal emulator program.

Note:

You can install the module in a local or remote rack. For remote rack installation,

the module requires EtherNet/IP or ControlNet communication with the processor.

1.2 Package

Contents

The following components are included with your MVI56-CAS module, and are all
required for installation and configuration.

Important:

Before beginning the installation, please verify that all of the following

items are present.

Qty.

Part Name

Part Number

Part Description

MVI56-CAS
Module

MVI56-CAS

Teledyne CA Slave Module

1 Cable RS232 Null

Modem

For RS232 Connection to the CFG Port

3 Cable Cable #14, RJ45 to

DB9 Male Adapter

For DB9 Connection to Module's Port

2 Adapter 1454-9F

Two Adapters, DB9 Female to Screw Terminal.
For RS422 or RS485 Connections to Port 1 and 2
of the Module

ProSoft
Solutions
CD

Contains sample programs, utilities and
documentation for the MVI56-CAS module.

If any of these components are missing, please contact ProSoft Technology
Support for replacement parts.

Содержание inRAx MVI56-CAS























































































Результаты поиска

Содержание inRAx MVI56-CAS

Отзывы:

Бренды по названию

Популярные бренды

ProSoft Technology inRAx MVI56-CAS, Руководство пользователя

Результаты поиска

Содержание inRAx MVI56-CAS

Отзывы:

Бренды по названию

Популярные бренды